Specifications
Main

Applies to
neoVI Yellow

Device Specifications
� 2 DSPs and 1 RISC processor for 88 MIPS of processing
� 1 MB message buffer* Power Consumption (typical) : 100mA @ 14.4 VDC
� Sleep Power Consumption (typical) : 8mA @ 12.0 VDC
� Power Supply: 5.5-32 Volt Power Operation
� Temperature Range: -40C to +85C
� Vehicle Connectors : 15 Pin male D-SUB
� General Purpose IO: 3 MISC IO (0 - 3.3V)
� General Purpose IO rate report interval: 1 Hz to 10 Khz or based on digital change
� Microsoft� Certified USB drivers
� Isolated USB 2.0 Full Speed Device backward compatible with USB1.1
� Stand-Alone Mode Including Scripting, Receive Messages, Transmit Messages, Expressions, IO, and Transport Layers
� RS232 host port with HW handshaking support for scripting and gatewaying network data
� ICS TimeSync for Multiple Hardware Synchronization supports all neoVI 3G devices
� J2534 and RP1210 A/B compatible for CAN/ISO15765, J1708, Keyword, and ISO9141
� microSD card slot support up to 12 Gigabytes of storage. The removable card is formatted using FAT32 for direct usage in a PC.
� Battery backed real-time clock (RTC)
� Warranty: One Year Limited Warranty
� Firmware: Field upgradeable design (flash firmware)

Networks - General
� 64 Bit time stamping to accuracy of 10 microseconds on networks and never overflows. 0.5 microsecond accuracy timestamp available if using one network only
� Simultaneous operations on all networks
� Transmit message double-buffering on all networks allows back to back message transmission

Network Specifications
2x J1939/CAN Channels

� 2 Dedicated ISO11898 Dual Wire CAN Physical Layer (TJA1040)
� CAN 2.0B Active
� Up to 1 M-Bit Software Selectable Baud Rate (auto baud capable)
� Capable of generating and detecting error frames
� Logic Analysis of CAN Waveform with 25 nanosecond resolution
� Graphical Bit Time / Baud Rate Calculator
� Listen only mode support* Unterminated network detection

J1708
� High precision time capture of J1708 bus events
� Software selectable parameters including baud rate
� SAE J1708 Physical layer

K and L Line, 1x LIN (Local Interconnect), ISO9141, or Keyword 2000
� UART Based State Machine
� Initialization Waveforms including Fast Init, Five Baud, and Custom
� Programmable Timing Parameters including Inter-Byte, TX Inter-Frame, RX Inter-Frame and Initialization Waveforms (0.5 ms Resolution) Full support for LIN 1.X, 2.X and J2602
� K and L have software controlled transmit enable lines allowing many different variants of UART or ISO9141 communications including:Tx on L Rx on K (full duplex);Tx and Rx on K (half duplex);Tx on K and L and Rx on K
� Socket selectable pull up resistor on both K and L lines
� Capable of Generating LIN Waveforms (Including Errors) Using Dedicated Output Compare Hardware
� Software Selectable Baud Rate
� LIN Bus Monitor Mode identifies errors : Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/Slave Not Responding, Checksum Error and Transmit Bit Errors.
� LIN Bus Master Mode operates at same time as LIN Bus Monitor
� LIN Bus Slave simulation - with or without an LDF file
� LIN Bus hardware schedule table with support for LIN diagnostics GM Class 2/ SAE J1850 VPW
� VPW Physical Layer capable ofTx and Rx operations in high speed modes (MC33390)
� Reception of IFR data during rx and tx
� Long Message transmit and reception for ECU flashing

 neoVI   Documentation - (C) Copyright 2000-2020 Intrepid Control Systems, Inc.

Last Update: Tuesday, January 08, 2013