Vehicle Spy 3 version 3.8.0.115 to RC 3.8.1.78 release notes

Bug Fixes
Device / Firmware	Device or Firmware Specific fixes
CoreMini	Fire2 and Fire2 VNET CoreMini now supports flash optimization
Explorer	Updated the neoVI Explorer's buttons to be more intuitive
	Added the ability to upgrade the Wireless neoVI Client on ValueCAN.rf using .WNC files
	Added the ability to configure Cellular networks on the ValueCAN.rf
	Updated the Misc IO Panels to support Fire2's new Enhanced Misc IOs
	Fixed a bug where IONs would need to be flashed twice to work correctly
	neoVI Explorer Device View is now more flexible for multi-chip devices
	Fixed a bug where ValueCAN.rf displayed MPIC version as CCHIP instead of MPIC
	ValueCAN.rf' s MAC Address is now shown in neoVI Explorer
	Added support for the Fire2's EMISC and MISC Pins (if equipped)
Extract/Export	Support for extracting from CoreMini versions older than v3.4.0.12 is no longer supported
	Added support for ValueCAN.rf LZ4 files with the command line extractor (required for WiVi support!)
	Missed or out of order extended filesystem records now generate an error
	Added support for 0E Extended records (allowing for 96GB in one record chain)
	Fixed SD Cards with extended records (i.e. FlexRay) extracting to higher than 100%
Firmware	Added support for the Fire2 VNET
	Fixed a bug where a flow control matching two messages on two networks would trigger both
	Fixed a J2534 bug where ISO15765-2 Transmits would accept a flow control from an incorrect network
J2534 DLL	Added support for Manufacturer Specific CANFD protocols in the J2534 driver (J2534 v404 only)
	J2534 accelerated ISO 15765-2 frames can now be done on two VNETs simultaneously
neoVI DLL	DPS flashing with the Fire2 is now faster than FIRE
	Updated the firmware in Plasma / ION to work with the 64-bit DLL
	Added support for RAD-Star2 in the DLL
neoVI FIRE2	Fixed a bug with non-ISO Fire2s where DWCAN networks wouldn't wake up correctly
	Fire2 now has a report message when Ethernet Link Status changes
	Fixed Fire2  values reporting incorrectly on startup
	Fixed the Fire2 Temperature Sensor Value being listed in the wrong neoVI Report Message
	Added support for the Text API client in the Fire2, allowing support for future add on devices
	Fixed the Fire2 Time Resync messages not beginning when they were supposed to
	Fixed a bug where duplicate Flow Control messages were seen in Vehicle Spy while flashing with DPS
	The NeoVI Report message now correctly reports the Red and Green LED status of the Fire2
	Fixed the Fire2 sending ACK in Listen Only mode on certain networks
PLASION	Reworked the FlexRay VNET code to be more efficient
RAD-Galaxy	Fixed a freeze bug when sending 70%+ CAN traffic on each network with the RAD-Galaxy
	RAD-Galaxy now has ISO CANFD enabled by default
	RAD-Galaxy OP-BroadR-Ethernet now reports link status changes
	RAD-Galaxy now supports listen only mode
	Fixed a bug where HSCAN messages wouldn't send if HSCAN was the only enabled network in RAD-Galaxy
	Fixed the GUI in VehicleScape DAQ to be more intuitive if 'Auto Start DAQ' is disabled
	Fixed a bug where RAD-Galaxy would show up twice in Extract/Export
	Fixed the RADGalaxy requiring a re-power after removing or plugging in an SD Card
	RADGalaxy will now auto negotiate 10/100/1000
	Fixed the RADGalaxy disappearing after sending certain scripts to CoreMini
	Fixed a RADGalaxy lockup when toggling power off and on multiple times rapidly
	Fixed a bug where CAN TX error count wouldn't reduce to 0 after a full recovery
RAD-Star2	Added support for RAD-Star2
SD Card Formatter	Added support for 64GB cards in the SD Card Format tool
	Forced the SD Card Format Tool to require Admin Rights (it still needed it before, but now it won't run without Admin Rights)
ValueCAN.rf	Fixed ValueCAN.rf Audio Files not being uploaded correctly to Wireless neoVI
	Fixed a bug where ValueCAN.rf Linux wouldn't enter low power sleep mode correctly
	Fixed the ValueCAN.rf' s system time reading as 1970 until a script is loaded
Vehicle Spy 3
C Code Interface	Added support in C Code Interface for Visual Studio 2017. The Open in Visual Studio button now finds VS 2017 correctly
CAPL Converter	Fixed A0 characters in CAPL code converting to white space, causing C++ compiler issues
	Fixed a bug where CAPL fileGetString returned an incorrect string on certain situations
	Fixed a crash when certain scripts are opening floating panels
Data Analysis	Fixed a bug when reading in Data Analysis cfg files
	Fixed the Data Analysis Output bar being wiped if certain areas were clicked
	Fixed a bug with Data Analysis where removing one graph would disallow new channels in another
	Fixed MDF values being displayed in scientific notation Data Analysis when they shouldn't be (i.e. 0.000e+00 instead of 0)
	Fixed the borders in Data Analysis resizing incorrectly when changing the window size
	Fixed the Ctrl+H hotkey not working correctly in Data Analysis
	Fixed a bug where Data Analysis would stop plotting graphs if channels were switched many times in a short period
	Fixed Data Analysis graphs disappearing when box zooming on multiple graphs
Ethernet	Made wildcards work in Ethernet Rx Messages like they should
	Moved each Ethernet network into its own TCP/IP stack
	Fixed the way that Ethernet Signal Data is worked with in the different views. Signals now persist and shift depending on what changes
	Fixed an External Exception when using Ethernet
	Fixed a typo on the TCP/IP GUI
	The TCP/IP view now updates correctly when parameters are changed by the FSA Replay Wizard
	Fixed the DoIP / TCP/IP View's header cells to no longer allow vertical resize
	Fixed numerous bugs and issues with the ARP Table
	Fixed an Access Violation when pressing 'Edit Ethernet Packet Templates' when ProtocolSignalDatabase.vsdb is missing
	TCP messages now try to reconnect to a new port once closed with Function Blocks
	Added support for wildcards in EtherType and IP Address
	The Ethernet Activation line (if equipped) now defaults to Off
	Fixed TCP messages not sending via Hotkey
Extract/Export	WiVi OneShot reports now have the start time appended to them
	Added the ability to extract data over USB using the API
	The Extract view now shows where the stored data exists on the overall timeline when connected
	Export to MDF for State Encoded use scaled inputs values when populating the state table
	Added an export option for just certain sets of data (i.e. use one channel list for multiple exports)
	Added an Export advanced setting to change the path for temp files during extract/export
	Fixed a bug where certain SD cards would extract with an incorrect folder timestamp in certain conditions
	Fixed an erroneous decoding of Bus Query DTCs
	Fixed a bug where exporting to both CSV and MAT files at the same time would get stuck on the last couple MAT frames
	Fixed a crash bug when extracting certain MDF files
FlexRay	Fixed an Access Violation with certain bad FIBEX files
	Fixed a bug where CAN filters wouldn't work properly in Review Buffer if 'display FlexRay PDUs' was on
FSA	Fixed a crash when trying to open a PCAP file in the FSA Replay wizard
GPS Maps	GPS Map position now syncs correctly with Messages View or Data Analysis
	Added the ability in GPS Maps view to show a 'history' or 'breadcrumb' mode
Graphical Panels	Fixed a flicker in the Graphical Panel Graph control
	Fixed messages attached to Tx buttons not adding to the Transmit table on Graphical Panel imports
	Fixed the Database Mismatch Scroll Bar's tooltip, which was showing HTML
	Fixed the Graphical Panel Message History's scrolling
	Fixed Ctrl+S opening certain text entry boxes on grids
	Fixed Graphical Panel being blank on minimize > restore until the user clicks
	Fixed certain Trig functions not working correctly
	The default Graphical Panel name now resets properly on File > New
	Fixed a random blank floating panel showing up after opening a different VS3 (without floating panels) from a VS3 with floating panels
Hardware	Fixed the  numbers not matching the neoVI Report messages with the Fire2
	Improper closing of Vehicle Spy (i.e. Crash) no longer requires all programs using the hardware to be closed
	If IEVB Firmware is mismatched (i.e. neoECU10, neoVI MOTE), 'Firmware is out of date' now displays in red
	Overhauled the Firmware Update dialog
	The CoreMini console now properly releases device handles when it's closed
	Fixed a bug where selecting 'Use Setup Baud Rates' could cause Vehicle Spy to hang or crash
	Added the ability to modify CAN-FD specific Network Properties in the Expression Editor
	Vehicle Spy no longer allows navigation while flashing device firmware
Main	Fixed a bug where LIN (Bitrate) property wouldn't return the correct rate
	Fixed a bug where the Tablet License would cause errors when trying to log to SD Card
	Routine Control Signals are now accessible by other parts of Vehicle Spy
	Function Block Start Type can now be changed in the grid. Fill Up / Down is also available
	Added the ability to group Application Signals into folders
	Added Statistics (Min, Max, Mean, StdDev) to Messages View column selections
	Added support for ISO 15765-2:2015 in Vehicle Spy
	Updated numerous things in the Expression Editor and made it more efficient
	Fixed the Graphical Panel Import not importing the initial value of Text type application signals
	The EtherType box in the Messages Editor for Ethernet Messages no longer allows invalid inputs
	Changing a Periodic On/Off button from On to Off no longer goes online first
	Fixed the signal selection in messages view not auto-resizing correctly when adding signals greater than 64-bits in length
	The Expression Editor's textbox is now larger, allowing easier creation of multi-expression steps
	Messages Editor now no longer allows pasting from non-compatible networks (i.e. CAN to Ethernet)
	Fixed a bug where Database jobs could be changed from Physical Request to Functional, which caused an Access Violation
	Added a textbox for Simulation Mode speed input
	Fixed a bug where the Extra Byte field in ISO 14229 ECUs would be disabled after clicking on certain areas in the Security tab
	Added support for many more AVB protocols in the Messages View Details pane
	Fixed a bug where the Application Signal Initial Value box would stay disabled when it shouldn't have
	Fixed a bug where the expression editor would add the wrong item for 'Available Disk Space (KB)'
	Fixed a bug when trying to set Read Only values in the Expression Editor
	Fixed the Select All and Select None buttons from disappearing from the Simulator tab
	Fixed a typo in the Expression Editor for Physical IO Switch Signals
	Fixed various GUI issues in the Diagnostics Setup tab
	Pressing 'Add to Expression' now adds at the cursor rather than the end of the expression
	Removed a duplicate 'AIN VNET Report Interval' signal from the Expression Editor's Misc > Time section
	Added numerous Expression Editor improvements, including an escape character so {} can be ignored as a variable (useful for Text API commands)
	Fixed a bug with State Encoded signals when matching text, if two states shared the same text, the signal would get confused
	Fixed a bug where sorting VSBs by line wouldn't work correctly
	Added support for UDS Extended Addressing
	Function Blocks that are set to Microsecond precision in PC Mode are now evaluated after every receive message
	Fixed external exceptions and Out of Memory crashes when opening extremely large VSBs
	Fixed a crash bug when generating certain setups
	Fixed a bug with Capture Blocks where the last frame of a ISO15765 message was replaced with the full payload
	Removed a duplicate 'Power Supply Voltage' entry from the expression builder
	Setting the number of Signal Plot points to a point where an Out of Memory error occurs now gracefully saves itself and displays an error instead of crashing
	Added support for New Line or Break characters in the Expression Builder
	Fixed a lockup when searching certain function blocks
	Adding and removing jobs in Diagnostics View Tree Mode no longer collapses the tree
	The last signal group used in the Logging tab is now saved correctly between sessions
	Fixed input lag when working with large files
	Fixed tab order being off in the ECUs view
	Applied the new Network Selector to the Network Column in the Networks View
	Renamed the CAN-FD EDL bit to 'FDF' (per the ISO 11898-1 Spec update)
	Fixed a bug where pressing 'Cancel' on the TextAPI Function Block Command screen saved the changes anyway
	Fixed an Access Violation when connecting to an EEVB with two instances of Vehicle Spy
	Read Only' signals from the expression editor no longer can be placed into 'Pick Set Value' expressions
	The Tx Panel no longer allows messages to be changed to and from non-compatible networks
	The "..." box in the Log Data setup dialog now is properly hidden when it's not needed
	J1939 PGNs from different sources are now separated on the Messages View
	Fixed a bug where Bus % Use could go to an unreasonable number in Simulation Mode
	Fixed an Access Violation when trying to open a non-existing A2L file
	Fixed a bug where Load Message Data's value would display 'Click to Setup' after it was already configured
	Fixed an Access Violation when opening certain VS3Zip files
	Fixed an Access Violation when generating certain CoreMinis
	Fixed the 'Ignore Tx Messages' box missing from certain non-CAN receive networks
	Fixed a List Index Error after using the Edit Widget dialog for floating panels
	Fixed another Access Violation when opening certain VS3Zip files
	Fixed an Access Violation when opening certain VS3s
	Signal Plot signal names now use Unicode characters, and no longer display weird text when used with non-US Operating Systems
	Fixed Log Data not logging the Rx Message Property B1-B8 correctly
	Added the ability to set WiVi settings for ValueCAN.rf in neoVI Explorer
	The Generate button now becomes disabled while generating
	Fixed a bug where ValueCAN.rf couldn't format the SD card if WiVi was enabled
Firmware is now stored in fw.bin instead of in the Vehicle Spy exe (reduces file size significantly)
Fixed a bug when streaming ASC buffers where extra blank messages were generated
DTC Import now supports UTF8, Unicode (Windows Little-endian) and Unicode Big-endian
Added support for ISO 15765-2:2015 frames
F-Keys are no longer usable when a modal dialog is displayed (Exception: F1 for Help)
Diagnostic Jobs now display key / index in Diagnostics
Fixed checkboxes in Network Databases
Added support for VSEB files - Vehicle Spy Encrypted Binary
Fixed Save Diagnostic Results saving file name with 2 timestamps
Added option to skip delays in Playback blocks
Fixed External Error: EEFACE when using VSB Editor with files from Data Cache Disk Streaming
Fixed a bug where the Networks color column didn't show network color correctly
Fixed an Access Violation when opening certain old setup files
Fixed an Access Violation when opening certain files when other files are already open
Fixed Function Block Set Value for network Error count
Fixed Split VSB to no longer allow the window to be closed when splitting
Changed the 'Automatically restart when complete' checkbox to allow a restart that resets the start trigger
Fixed some unintended slowdowns when Pre/Post 'Number of messages' was extremely low
Fixed a bug where editing Test DTC made the command stop working
Fixed degree symbol not showing correctly as a unit
Fixed a bug where cutting Jump To / Jump If blocks
Diagnostics search boxes are no longer case sensitive
Fixed issues when handling non-zero STMIN values
Fixed an Access Violation or Abnormal Program Termination when closing certain floating GP Windows
Fixed a bug where logged CSV files wouldn't save Time (abs) correctly
Fixed jumbled labels in Signal Plot when reordering signals
Fixed an Access Violation when opening certain VS3Zip setups
Fixed the Network Baud Rate mismatch warning from staying stuck with certain setup / hardware configurations
ECU Name is easier to see in the Diagnostics view
Fixed an Access Violation in the LDF tool in the Frames tab
Changed the label text 'Path' to 'File' in the VSB Editor, Split VSB and Remap VSB tabs
Fixed LIN message length to not allow incorrect entries
Fixed the Extra Bytes window from causing erroneous inputs if the user clicks off the window without closing it
Fixed the Extra Bytes window from losing focus after entering certain types of values
Fixed a bug with Hex Signal Values not scaling correctly when using non-integer values
Fixed a bug with certain non-CAN networks adding extra bytes unintentionally after clicking
Fixed J1939 Address Status Request not sending on startup correctly
Fixed PID requests not working when imported from certain ODX files
Switching between Physical and Functional addressing in J1979 Jobs now correctly updates the ArbID
Fixed the Sort icon in the Network Selector to be a bit more clear which way it's being sorted
Fixed State Encoded signals displaying incorrect decoding with undefined invalid states
Fixed the 'Run' box sometimes not displaying 'Monitor Only' when using Run Monitor Only
Fixed a bug where deleting a signal or message wouldn't autoselect the next signal or message
Fixed a bug where the MIC2 with ValueCAN.rf wouldn't set the date correctly
Fixed a bug with the MIC2 and ValueCAN.rf where logged GPS data was logged without an ArbID or timestamp
Fixed the ISO ECU Length of Memory Address in bytes not loading correctly
Connecting to more than one copy of Vehicle Spy over TextAPI now changes ports correctly
Added periodic reporting of GPS data with ValueCAN.rf
Fixed RADGalaxy not catching and displaying errors for IPv4 messages with a bad checksum
Fixed a Cascading Access Violation in the Tools > Utilities > Language tab
Fixed TCP signals in later bytes causing the GUI to resize incorrectly
Fixed the ECUs Wizard 'No conflicts found' popup getting stuck behind the main VSpy window
Fixed the GPS Maps 'On Change Only' checkbox, which had 3 states instead of 2.
Fixed CoreMini not being able to read ISO9141 signals in Function Block Scripts
Fixed the CoreMini error message: 'Hardware License does not support SD card logging operations.' when it shouldn't have
Updated ASC and BLF exporting to the latest spec for CAN-FD
The ARXML Importer now shows what's loaded in the current platform, not what was last configured
Fixed certain signals not being aligned correctly on PDX Import
Fixed TextAPI when using to access Function Block Steps
Vehicle Spy now is much more stable when simulating extremely large simulation files
Fixed TextAPI's Start command from always reloading the platform each time it was used
ARXML Import now correctly merges messages from common IDs
Fixed a bug where copying Jump To or Jump If commands between two function blocks would change the jump step
Fixed the J1979 DTCs not being decoded correctly when trying to decode a multiframe (i.e. more than 3 DTCs) DTC response
Fixed Plasma needing a power cycle after doing J2534 reflashing
MEP	Fixed an Access Violation when opening certain older setups
	MEP > Setup: the Auto-reconnect checkbox now saves with the setup file
	Fixed XCPoE Signals having an incorrect offset
	Significantly reworked XCPoe behind the scenes
Messages View	Fixed a bug where you could try to filter line numbers or absolute time in scroll mode
	Fixed the Messages View Details pane to now decode LIN correctly
	IEEE 1722.1 messages now display correctly in the Details pane on the Messages View
	Fixed Review Buffer's streaming displaying line numbers instead of message numbers
	Fixed the Messages View FSA Columns showing Hex data while Decimal mode is selected
	Fixed the way that CAN Bus errors are shown in the messages view during Simulation
	Time columns now go down to nanosecond precision with supported devices
	The Details pane now highlights the raw hex values when you click on a name or value
	Fixed the Messages View not refreshing correctly when selecting a signal label in Data Analysis
	Fixed a bug where Static Mode would identify a J1939 CTS/RTS as the incorrect PGN
	Fixed a crash bug when filtering using commas and rapidly typed text
	Fixed the Signal Decoding for the MSRP emergency bit being backwards
	Fixed a bug where AVDECC Discovery Protocol Messages were incorrectly decoded by the details pane
	Fixed the BLF exporter to no longer allow invalid entries
VehicleScape DAQ	Improved Function Block to Wireless neoVI communication
	Fixed VehicleScape to never go online automatically when Auto Start is disabled
	When selecting ECUs for a Bus Query, selecting ECUs with no ArbID is no longer allowed
	The Gateway Clean button is now properly disabled when Vehicle Spy is online
	Fixed the VehicleScape DAQ Standalone Logging 'Clean' button not removing the links to the VSDBs correctly
	Added support for XCPoE (XCP over Ethernet)
	Fixed a typo in the VSSAL Partition Manager function block
	Fixed the 'Do not restart when collection is finished' option being grayed out on Pre/Post collections
	Fixed Generate Gateway not compiling with certain channels selected
	Fixed Gateways getting generated when they weren't supposed to
	VehicleScape DAQ Bus Query now supports Mode $03, $04, $07, and $0A
	Fixed a bug with XCP DAQ decodings not being properly generated
	Added Password field in VehicleScape DAQ Standalone Logging tab
	DAQ settings now properly update display properly when switching from DAQ1 to DAQ2
	Fixed the CoreMini Generator message box silently failing to open when certain problem logs were present
	Fixed Histogram collection when Linear bucket spacing was selected logging incorrectly
	Fixed an Access Violation when loading certain XCP DAQ setups
Video	Added support for Video Processing
	Added support for the new Video form in Simulation / Review Buffer
	Added support for Camera Audio logging and Playback / Simulation

Vehicle Spy 3 version 3.8.0.114 to 3.8.0.115 release notes

Major New Features	This list will be in the What's new video
	neoVI FIRE2 can now use CoreMini
	RAD-Galaxy is now a fully fledged Logger and Bench tool
	New VehicleScapeDAQ UI
	New Network Selector UI
Limitations / Errata
Bug Fixes
Fire2 Firmware	Fixed a bug with Fire2 CoreMini where 29-Bit SWCAN was logged as CAN-FD
VehicleScapeDAQ	Fixed a bug with Histograms with Linear Buckets not logging correctly

Vehicle Spy 3 version 3.8.0.111 to 3.8.0.114 release notes

Major New Features	This list will be in the What's new video
	neoVI FIRE2 can now use CoreMini
	RAD-Galaxy is now a fully fledged Logger and Bench tool
	New VehicleScapeDAQ UI
	New Network Selector UI
Limitations / Errata
Bug Fixes
3G Explorer	Fixed a bug where Updating Android would reset the focused window to the Connect screen, causing confusion
Main	Fixed a bug where the Vehicle Spy Trial couldn't view bus traffic
	Updated copyright information on all modules for 2017
	Fixed a bug where CANFD ISO15765 Long messages with static bytes weren't filtered correctly
	Fixed a bug where in some cases multiframe messages were not transmitted properly.
	Fixed a bug where ISO ECU Memory Address Length properties weren't saved or loaded correctly.
MEP	Fixed a bug where XCP addresses weren't saved correctly
Messages View	Fixed a bug where CSV files weren't reviewed correctly by Review Buffer
VehicleScapeDAQ	Fixed a bug when trying to extract logged DLT files
	Fixed a bug where certain Finish expressions wouldn't compile correctly
	Fixed a bug where certain VSSAL Stop expressions wouldn't compile correctly
	Fixed a crash when Log All Updates was selected in PC Logging

Vehicle Spy 3 version 3.8.0.105 to 3.8.0.111 release notes

Major New Features	This list will be in the What's new video
	neoVI FIRE2 can now use CoreMini
	RAD-Galaxy is now a fully fledged Logger and Bench tool
	New VehicleScape DAQ UI
	New Network Selector UI
Limitations / Errata
Bug Fixes
Ethernet	Fixed some settings on the DoIP page not 'sticking' when saved
Firmware	Fixed a bug where HSCAN 4/5 wouldn't wake up the device if 'Instant Wake Up' was selected
Main	Fixed a bug in Analysis / Simulation Mode where all xtd SWCAN ArbIDs were reading as x0
	Fixed a bug where the wrong value would be calculated if using Set Value with a decimal in the denominator
	Fixed a bug where Text DIDs weren't read out correctly
	Stream to Disk now saves all data regardless if there's a stop/save or not
	The 'Inherit MAC Address' option in TCP/IP View now works correctly with the Fire2
	Fixed a memory leak when using a RAD-Galaxy for extended PC logging (i.e. 'over the weekend')
	Fixed a bug where certain scaling values caused signals to be imported incorrectly
	Importing ARXML files with 'CAN-Frame-Tx-Behavior' (or Rx) set to CAN-FD now import correctly as CAN-FD messages
	Fixed a bug where the ABS Time column would get stuck at the beginning value
VehicleScape DAQ	Fixed a bug where AnalogIn Data was recorded as HSCAN messages instead of neoVI Messages
	Fixed a bug where Single PID Requests would send out as 0000

Vehicle Spy 3 version 3.8.0.98 to 3.8.0.105 release notes

Major New Features	This list will be in the What's new video
	neoVI FIRE2 can now use CoreMini
	RAD-Galaxy is now a fully fledged Logger and Bench tool
	New VehicleScape DAQ UI
	New Network Selector UI
Limitations / Errata
Bug Fixes
CAPL Converter	Added a Select Folder option in the CAPL Converter to handle Canoe Panels
Data Analysis	Fixed certain signals not showing in Data Analysis
Firmware	Set Value now works in RAD-Galaxy CoreMini
	Fixed a bug where the Fire2 would sleep at too low of voltage for CAN
	Fixed a bug where RAD-Galaxy CoreMini would lock up sending CANFD messages
	Fixed a bug where the SRR bit wasn't being set correctly for 29-Bit ID SWCAN
	RAD-Galaxy can now send out Remote Frames properly
	Fixed a bug where SWCAN2 wouldn't transmit correctly after waking up with a RAD-Galaxy
	Fixed a bug where the Fire2's CAN Chips wouldn't properly go into Listen Only mode
	Fixed a bug where extracting from RAD-Galaxy over Ethernet would show a different amount of messages than extract over SD Card
	Increased the RAD-Galaxy data extraction speed
	Fixed a bug where the Fire2 wouldn't go to sleep if in selectable SWCAN Mode
FlexRay	Fixed a bug where Flexray Channels Setup options weren't being saved properly
Graphical Panels	Fixed a Text Entry box turning grey when it shouldn't
J2534 DLLs	Fixed PassThru returning False for RAD-Galaxy if CANFD termination Get/Set was called
	Added support for RAD-Galaxy in our J2534 DLLs
Main	Fixed an Access Violation on the Extract / Export tab if a RAD-Galaxy was disconnected.
	Fixed an out-of-memory error message if trying to set a Setup Calculated Signal with a rate of 0
	Made the Security Box on the ECU View's Identifier's tab easier to read
	Fixed an extra space that was added to capture blocks saved name when 'Append App Signal to File Name' was checked
	Fixed a bug where RTC couldn't be synced on Dec. 31 on a leap year
	Added software support for our new ION PCIe Modems
	Fixed a crash if attempting to close Vehicle Spy while trying to go online.
	Updated the copyright. Happy 2017!
	Fixed an ARXML signal not being imported correctly
	Fixed a bug issue with logged DLT data not extracting
	Addressed Tx Rx Message Matching for OP(BR) Ethernet networks
	Fixed a bug with certain setups where a counting down timer would jump between 0 and the counting down number
	Fixed 'the following protocols are unsupported' when converting a VSB to ASC.
	Fixed PDX Import not implementing certain DID Min-Max value ranges correctly
	Fixed an Access Violation when scrolling Signal Plot's X-Axis while online
	Fixed an Access Violation when reviewing a buffer with SW High Voltage ArbID checked
	Added a DLL API call to translate the new Base36 style serial numbers into strings (i.e. Fire2: CY0001)
	Files with very high amounts of function blocks now load faster
	Fixed a bug in Signal Plot where, depending on what was in the buffer, you would see two incorrect points connected
	Fixed a bug where VSB version 103s were read wrong in Streaming Mode
MEP	Fixed a bug with MEP's 'Value characteristic Editor' where the data would look to be changing even though it was constant
VehicleScape DAQ	Fixed a problem with two Flow Controls if a DID is in the Channels list and the Bus Query list

Vehicle Spy 3 version 3.7.1.87 to 3.8.0.98 release notes

Major New Features	This list will be in the What's new video
	neoVI FIRE2 can now use CoreMini
	RAD-Galaxy is now a fully fledged Logger and Bench tool
	Video (Axis and web cam)
	New VehicleScapeDAQ UI
	New Network Selector UI
Limitations / Errata
Bug Fixes
neoVI Explorer	Added IFS shift panel for Slave VNETs
	Added Selectable CAN Termination for Fire2
	Changed "Selectable CAN" to "Selectable Networks" for the Fire2 VNET
	Changed default for "Send Bus Traffic to Android" to Enabled
	Explorer can now check Linux version and SD Card content even if not fully connected and powered
	Fixed a bug where Load Defaults would enabled J1850 on a Plasma (which doesn't support it)
	Fixed some panels using Textboxes instead of Labels
	Fixed the scrollbars not working for Product Details and Available Firmware
	Fixed the SD Card Test not working correctly
	Made it clearer how to change Selectable CAN
	neoVI Explorer now populates available settings after the device is connected
	UART and LIN now correctly grey out when disabled
CAPL Converter	Fixed a bug when converting certain J1939 CAPL Projects
	Fixed an import issue on certain CAPL projects
	Fixed CAPL Conversion on certain setups
CoreMini	Added a warning that CoreMini only supports 3 nested loops
	Added a warning to the CoreMini Compiler if a Replay block contains negative timestamps
	Axis F44 Cameras are now supported in CoreMini
	Fixed a bug where CCP polling wouldn't work if CoreMini Optimization was turned off
	Fixed a bug where copying Rx Message Bytes to Tx Message Bytes wouldn't always work
	Fixed an Access Violation when running CoreMini compiler on particular UART setups
	Fixed AutoTx on Rx not working on certain networks
	Fixed Message Bx property for Ethernet Messages
	Fixed neoVI Mote triggers sporadically being missed by the device
	Fixed the Message BX property not working properly in CoreMini
	Fixed Wait Until with Timeout not working properly on neoECU10
	Tx Message Count property now updates when it should for all CoreMini messages
Data Analysis	Data Analysis now supports MF4 files
	Data Analysis Zoom 'distance' is now more consistent
	Fixed a bug when saving signal data in Data Analysis
	Fixed a bug where Data Analysis MDF files weren't saved correctly
	Fixed a bug with Data Analysis where Duplicate Records would corrupt table view
	Fixed a crash in Data Analysis after changing tabs
	Fixed a crash in Data Analysis when switching between two files
	Fixed a crash with Data Analysis
	Fixed a crash with Data Analysis when importing CAN-FD VSB Files
	Fixed an Access Violation in Data Analysis while Vehicle Spy is running
	Fixed the Data Analysis Open File Dialog, it now shows MAT files when "All Supported" are selected
Ethernet	Added support for PCAPNG files (for Ethernet)
	Added support for reading Ethernet in ASC files
	Diagnostics View Tree / List now displays DoIP Information if the job is a DoIP Job
	Ethernet logging now starts quicker
	Fixed a bug that caused an Access Violation (and all Ethernet NICs to disappear) with certain WiFi adapters
	Fixed a bug where Ether Type IEEE1722 would be saved missing a few parameters
	Fixed a bug where IPv4 UDP/TCP Frames would display the incorrect port on the Messages View
	Fixed a bug where the EEVB could try to transmit before the driver was fully initialized
	Fixed a bug where Tx Ethernet Message Signals weren't updated correctly by Function Blocks
	Fixed a crash when sending too short of Ethernet Messages
	Fixed an Access Violation after removing networks
	Fixed an Access Violation when using the Tx Panel to change VLAN Setting for an IPv4 Ethernet message
	Fixed an issue with TCP Payload causing flickering in the Messages View
	Fixed IP and Port from getting reset when protocols are switched
	Fixed 'Message Data' property for Ethernet messages not grabbing the correct section
	Fixed Vehicle Spy from sending ICMP "Port Unreachable" when receiving UDP messages
	Improved the way that Ethernet messages are handled so the 5000 Unique Message Limit isn't hit so quickly
	Increased TCP/IP to allow up to 128 connections at once in Vehicle Spy
	Listen for incoming TCP Connections is now a selectable property of Ethernet Rx Messages in Expression Editor
	Modifying signal size of Ethernet Messages now properly works with mouse dragging
	Removed the '5000 Unique Message Limit' on the Messages View
	Standard Ethernet signals are now editable
	TCP Network Transmit Messages now open new TCP connections properly
Extract / Export	Exporter now selects VSDB Signals by default
	Fixed a bug where Review Buffer didn't open from the Extract/Export page
	Fixed a crash while using VSA Extractor
	Increased the file limit for the Extractor above 2000 files
	Added a timeout in Extract/Export if we detect a SD Card issue
	Added additional information to the extracted Notes.txt file: names of the VSA records, and if the card was wrapped
	Diagnostic file names are now included in the XMLs from Extract/Export
	Ethernet is now supported in ASC Files
	Extract now stops if there's no more room on the hard drive
	Fixed a bug when exporting a negative 2's complement integer
	Fixed a bug where Bus Query DID Decodings were incorrect
	Fixed a bug where CSV timestamps could be thrown off by discovery messages
	Fixed a bug where local time conversion happened twice on certain messages
	Fixed a bug where some data would be lost when extracting an overlapped card
	Fixed a crash if the export was cancelled partway
	Fixed an Access Violation when clicking 'Remove Unused' in the Export Tab
	Fixed an Access Violation when going to File > New while extracting
	Fixed an incorrect DTC Status decoding from XML Report from Extract/Export
	Fixed an Index out of Bounds error when removing unused signals in Extract/Export
	Fixed combining VSB files using Ctrl+Shift+B
	Fixed Multiplex signals not exporting correctly
	Fixed some GUI Artifacts on Export Tab Checkboxes
	Fixed the Extraction Start/End Time from resetting to default if "Advanced Settings" was clicked
	MDF Extension in Extract/Export now shows MDF Versions
	Retooled the Messages Editor to be a bit easier to use with Ethernet Messages
Firmware	Added 5M CAN-FD baud rate, and baud rate setting controls for HSCAN2-7 to the API
	Added a tab in the API Helper tool to show installed DLL Versions
	Added an Ethernet Settings panel for applicable devices
	Added an option for all Ethernet Transmits to be padded to 60 bytes
	Added API support for parallel transmits of Long messages (for supported devices)
	Added API Support for reading FlexRay and MOST with compatible devices
	Added API Support for Slave VNETs
	Added support for ISO15765-2 Messages with CAN-FD
	Added support for selectable CAN Termination in the J2534 API
	DeviceID is now 1 after PassThruOpen succeeds
	DPS Support now exists for CAN-FD
	Fixed a bug when using SWCAN ISO15765-2 messages
	Fixed a bug where a Fire2 could get in a state where it wouldn't transmit Ethernet and require a repower
	Fixed a bug where a FireVNET would lose communication
	Fixed a bug where a LIN3 or LIN4 buffer overflow would lock up those buses until next power cycle
	Fixed a bug where Fire2 or Plasma/Ion would read incorrect values for Battery Voltage
	Fixed a bug where FlexRay overflow messages were logged as ISO9141 Frames
	Fixed a bug where SW2 would not trigger a wakeup
	Fixed a bug with ISO Fire2s where a shorted bus wouldn't recover correctly
	Fixed a bug with Timestamp Resyncs on Fire2 and Fire VNET
	Fixed a DLL Buffer Overflow with RADGalaxy
	Fixed a Message Packet Frame Error when going online with the EEVB
	Fixed an EEVB lockup when sending oversized messages
	Fixed API error text on certain conditions
	Fixed CAN Termination settings not 'sticking' after a Fire2 Reflash
	Fixed messages being overwritten when a buffer was overflowed
	FlexRay VNET now handles bad frames better.
	Increased the size of the Ethernet Tx buffer on Fire2s for better performance
	ISO CAN-FD (if available) is now the default CAN-FD Mode
	NeoVI DLL now no longer writes settings to the hardware if nothing's actually changed
	Updated the API to allow for CANFD and Ethernet transmitting
FlexRay	Added a scrollbar to the ECUs View Flexray configuration tab
	Added remote wakeup option for Flexray
	Added significant improvements to the Flexray Clusters Data View
	Added some new features to Flexray Cluster view
	Added some tweaks to the handling of partial Flexray frames
	Added support for Flexray in Simulator
	Changed Flexray Clusters View to more reflect its function
	Changed the way that NULL Flexray frames are handled in the Messages View
	Fixed a bug that would hide the Cluster Drift Dampening in ARXML from the user
	Fixed a bug when loading clusters from certain Flexray ARXMLs
	Fixed a bug when setting a hotkey for a Flexray message where the same hotkey was set for all other present Tx Messages
	Fixed a bug where certain FlexRay Databases weren't being imported correctly
	Fixed a bug where Flexray NULL frames sent by Vehicle Spy weren't caught by the Tx filter
	Fixed a bug where Flexray receive messages were decoded as Report Messages on CAN
	Fixed a bug where Flexray settings were saved even if the setup doesn't use Flexray
	Fixed a bug where Flexray values would be set to default when the POC is set to ready
	Fixed a bug where Null frames and Raw frames for Flexray were caught by the same discovery message
	Fixed a bug where the Flexray Restart Cluster action needed to be pressed twice to actually restart the nodes
	Fixed a bug where the Flexray slot ID wasn't saved correctly
	Fixed a bug with Flexray where an Rx message would decode more than it was supposed to
	Fixed a bug with Flexray where Tx messages with Slot ID > 839 was only seen as a Rx message
	Fixed a crash when changing Flexray Startup Sync/Slot ID
	Fixed a missing scrollbar on Flexray Cluster view
	Fixed an Access Violation in Flexray Cluster view
	Fixed an Access Violation in Flexray ECU Configuration tab
	Fixed an Access Violation when editing an ECU's Flexray Configuration
	Fixed an Access Violation when going online with more than 128 Flexray Tx messages configured for one node
	Fixed an Access Violation when reviewing certain VSBs
	Fixed an External Exception when pressing the Execute button in Flexray Clusters
	Fixed Database Import of State Encoded FlexRay messages not importing correctly
	Fixed Flexray decoding of POC State and CCSV Register to be displayed correctly
	Fixed FlexRay PDUs displaying incorrectly when reviewing FlexRay ASC files
	Fixed getting Flexray Clusters stuck in a certain state if 'Restart' is pressed too many times
	Fixed Node Settings in Flexray Clusters to be saved with the VS3
	Fixed the Rate counter to be more accurate with Flexray
	Fixed up Flexray Symbols to display correctly in the Messages View
	Fixed up some bugs in the FlexRay simulator
	Flexray can now use wildcards for a byte entered in Hex
	Flexray ECU Configuration tab now disappears if ECU network is switched
	Flexray frames imported from ARXMLs no longer filter out NULL frames
	Flexray messages can now be imported from FIBEX databases
	Flexray now displays length of messages correctly
	Flexray NULL messages are now decoded if they're found in the database
	Flexray POC State now changes properly when faced with error conditions
	Flexray raw traffic is supported in Basic
	Flexray Slot IDs are now displayed in Dec
	Frame HCRCs are now displayed on ECU Settings for Flexray Cluster View > Setup page
	Frames in Flexray Clusters View now show before going online
	Improved the Flexray Message Buffers view with some tweaks
	Made multiple improvements to the Flexray Cluster Setup page
	Reworked the Flexray Cluster View > Cluster Setup page
	User now has the option to select Continuous or One-shot mode for Flexray Tx Messages
	Users can now change the length of Dynamic Tx Flexray Messages while online
FSA	Added properties in the Expression Editor to control FSA Header Information
	Fixed a bug where FSA wasn't decoded correctly
	Fixed a bug where Simulation FSA messages weren't displayed in the Messages View
	Fixed a crash when changing a message's network from FSA to any OPBR network
	FSA buffers now show the correct source node in the messages view
	FSA byte signals are now editable
	FSA Properties can now be edited in Function Blocks
	FSA Replay Wizard's generate button now properly refreshes views
	Message Properties B1-B8 are renamed to their equivalents in FSA messages
	Vehicle Spy now handles FSA messages with large payloads more gracefully
	When using FSA Replay, the names of the autogenerated messages are a bit easier to understand
Graphical Panels	Added a Bring to Front option for floating panels
	CTRL+Clicking an item no longer selects objects behind objects in Graphical Panels
	Fixed a bug when importing Graphical panels where Application Signal Arrays were imported as separate signals
	Fixed a bug where Graphical Panel Imports wouldn't create Application Signals correctly
	Fixed a bug where graphs in floating panels where they didn't stay in place when scrolling
	Fixed a bug where importing a Graphical Panel would add messages that were already defined
	Fixed a bug where State Encoded Signals wouldn't show properly on Graphical Panels
	Fixed a bug where the Messages View on Graphical Panels where signals decoded as blanks
	Fixed a crash with certain VS3s
	Fixed an Access Violation and Crash when removing signal plot items while online
	Fixed an Access Violation on certain older setups
	Fixed an Access Violation when changing graphical panels on certain setups
	Fixed an Access Violation when trying to connect two Radio buttons to a DID with two signals
	Fixed an Access Violation when using floating panels
	Fixed an invalid class error when opening a Floating Panel
	Fixed the Calculator allowing you to add mathematical operators that didn't make sense
	Fixed the text with Graphical Panel Knob Controls from overlapping the knob
	IP Addresses now display correctly on a Graphical Panel
	Made the number of Signal Plot points on Graphical Panels user-customizable
	Moved meter captions to underneath the meter on Graphical Panels
	The pause button in the Graphical Panel Graph control now pauses collecting (as opposed to just pausing tracking)
Hardware	Fixed a bug where if Multiple Devices was checked, Autodetect hardware wouldn't work properly
	Fixed Ethernet stack to not send Ethernet messages if hardware doesn't support it
	Fixed up a few misc items on the Networks View
	Networks table now correctly shows baud rates for Fire2 HSCAN6/7
	Removed the 'Report GPS Coordinates' option for Non-GPS enabled devices
	Slave VNET Transmission has been greatly improved
	Slave VNETs now clear the LIN Slave table when going online
	The Messages Editor's Network Selector has been totally redesigned!
	The Networks View now shows CAN FD Baud Rates in the Messages View
	The Restricted Mode page now shows the connected serial number
	The VNET MPIC Updater is now more robust
	Vehicle Spy now checks for Baud Rate mismatches on Slave VNETs
	Added the option to start CoreMini even if USB is connected for certain devices
	Changed the names of some neoVI messages to not include 'PLASMA' as they're used on ION and Fire2 as well
Main	A problem log will now show if we were unable to open a CSV file for logging or writing
	Added a 'Function Block Execution Steps' box, which controls how many steps are run each core loop
	Added ASCII option for Diagnostic Signals
	Added line wrap to Function Block Comments
	Added Network Fix Popup on BLF Converter
	Added option to remap networks in VSB Split/Combine
	Added support for Big Signals (signals > 8 Bytes are now fully supported!)
	Added support for CAN-FD .BLF Files
	Added support for GM ARXML version 4.2.2
	Added TCP to Tx Panel Protocol List and sorted it
	Added the ability to import ECU messages from Flexray ARXMLs
	Added the currently used license type to the Title Bar
	Added up / down arrows to allow sorting of Function Blocks and App Signals
	Added Video Recording and Processing support
	After saving saved Zipped MDF files, the unused MDF is now cleaned up
	Appending signal values to Capture Block names now works as intended and ignores reserved characters
	Application Signal "Cut" is disabled when online
	Application Signal Toolbar Delete and Cut are disabled while online
	ASC Import now works for Flexray
	Binary ArbID Entry is now working as intended
	Bit Shading in Messages Editor now supports longer signals (and doesn't fade to white)
	BLF Files will now correctly display the Network Fixup when imported with unknown networks
	Capture Block "Buffer" tab renamed to "Filter" for ease of use
	Changed EDL to FDF for CAN-FD (name was updated per ISO Spec)
	Changed the text for creating LIN Schedule Tables to be more descriptive
	Changing a message color in the Tx Panel now correctly changes color in Messages Editor
	Completely reworked the Capture Function Block code to be more efficient
	Custom Format can now use Left-side padding
	Database equations can now be copied
	Deleting items in Extra Bytes table now shows Blank instead of 00
	Device Serial Number now will show Fire2 Serials correctly
	Disabled 'Pre Start Collection' in PC Logging when Start Automatically is selected
	Empty State Encoded signals will prompt the user for entry before saving
	Extensible Security now works for CANoe Security Access DLLs
	Extract and Delete buttons are now unclickable in Extract / Export if no files are selected
	Fixed a bug in Capture Function Blocks where clicking Append Signal to File Name would also check Append Date/Time
	Fixed a bug in CSV buffers where multiframe messages had the full payload on the last message
	Fixed a bug when importing a VSDB as a database that contained Tx Messages
	Fixed a bug when saving a VS3Zip to a folder where a VS3 with the same name already exists
	Fixed a bug when saving ASC files where it would say '0 messages skipped'
	Fixed a bug when trying to reopen an already open VS3Zip
	Fixed a bug where "Add First Element" in Expression Builder would only work once
	Fixed a bug where a CoreMini was too large when Optimization is off
	Fixed a bug where a function block import would create redundant messages
	Fixed a bug where a user could type into a label on the Choose VSB Method Dialog
	Fixed a bug where ASC files would jump to negative timestamps
	Fixed a bug where ASC files wouldn't decode
	Fixed a bug where CAN-FD messages displayed incorrectly when matching multiple filters
	Fixed a bug where certain files would crash Split VSB
	Fixed a bug where changing a function block Transmit step could modify a currently TXing message
	Fixed a bug where clicking outside of a box in Tx Panel still had it think it was clicked
	Fixed a bug where CSV Files would actually be VSBs just saved as a .CSV
	Fixed a bug where digital signals could get set in an unknown state in Function Blocks
	Fixed a bug where DoIP TCP Messages would state Invalid Node
	Fixed a bug where editing payload bytes in the Tx Panel for TCP Messages didn't work correctly
	Fixed a bug where Fire2 LIN Baud Rate wasn't changing properly with Function Blocks
	Fixed a bug where Functional Requests would stop decoding after the first positive response
	Fixed a bug where having two identically named ECUs would confuse the Node lookup
	Fixed a bug where ISO15765-2 Overflow messages were ignored
	Fixed a bug where J1939 DM1 monitor Flash Lamp status would be different depending on if you were in Scroll mode
	Fixed a bug where J1979 ECUs wouldn't be exported to ODX correctly
	Fixed a bug where J1979 jobs couldn't copy
	Fixed a bug where J1979 PID 0 wasn't being saved in the VS3
	Fixed a bug where MDX without Routines wouldn't import correctly
Fixed a bug where Min and Max values wouldn't show the correct values for 2's Compliment integers
Fixed a bug where only the first Routine Signal would be exported for ISO14229 ODX files
Fixed a bug where particular VS3Zip files would throw an error and not load correctly
Fixed a bug where remote frames weren't seen by a Fire2
Fixed a bug where 'Run with Transmit' would override the 'Disable All Tx' Button
Fixed a bug where Simulator wouldn't send out correct values
Fixed a bug where Standard DIDs could override customer-entered DIDs
Fixed a bug where State Encoded Signal States would get lost when switching from HEX to DEC
Fixed a bug where static bytes after a blank byte wouldn't be sent correctly
Fixed a bug where the ASC Network Fixup wizard could be left blank
Fixed a bug where the Auto Tx would switch back to default if you clicked the dropdown arrow
Fixed a bug where the Capture Function Block Data Tab was always blank
Fixed a bug where the Encrypt Bytes button would be removed if you deleted an encrypted Security Level
Fixed a bug where the Expression Editor's Test button would remain disabled
Fixed a bug where the Extra Bytes "Fill" feature skipped "FF" as a value
Fixed a bug where the first byte wasn't copied over correctly for Tx Multiframes
Fixed a bug where the first instance of an ISO15765 message wasn't sending data bytes correctly
Fixed a bug where the Flow Control Filter CAN-FD Flag wasn't persisting between saves
Fixed a bug where the Messages Editor Signal Add button would switch from add 64-bit to add 32-bit signal
Fixed a bug where the network fixup wizard would show twice
Fixed a bug where the Network Fixup Wizard's grid dropdown would remain visible after clicking elsewhere
Fixed a bug where the On Network would become 'desynced' from the table below in Messages Editor
Fixed a bug where the screen widget for Floating Panels wouldn't open said panel
Fixed a bug where the Tx Panel GUI Columns would get resized strangely
Fixed a bug where the Tx Panel Periodic On/Off button didn't update correctly if changed via Function Blocks
Fixed a bug where the Up and Down arrows in Messages Editor would duplicate a message
Fixed a bug where the Vehicle Spy Play Button text would get stuck at "Go Online"
Fixed a bug where under certain conditions Signals weren't updated correctly
Fixed a bug where Update Rate (rel) was either 0 or 1
Fixed a bug where User Signals didn't show up in the Expression Editor
Fixed a bug where UUDT Response IDs weren't exported correctly
Fixed a bug where VehicleScape wouldn't wait the full STMIN in ISO 15765-2 messages
Fixed a bug with ASC File Conversion where timestamps were set to now, not source data
Fixed a bug with CAN FD Multiframes causing a crash
Fixed a bug with CAN-FD where long messages weren't updated with every transmit
Fixed a bug with J1979 Multi-PID Requests
Fixed a bug with Simulator where closing with X would cut bytes off of an extra bytes string
Fixed a bug where Simulator wouldn't show the messages correctly in Simulation mode
Fixed a bug with Simulator where default message bytes weren't transmitted properly
Fixed a bug with timestamps when converting from VSB to CSV
Fixed a crash and Access Violation if clicking while a very large VSB file is saving
Fixed a crash if the Capture Block Buffer size was too small
Fixed a Crash in ECU Simulator View
Fixed a crash under certain conditions after going online on the messages view
Fixed a crash when attempting to load an invalid CSV file.
Fixed a crash when exporting certain ISO14229 ODXs
Fixed a crash when going online while switching Views
Fixed a crash when saving PCAP files when reviewing in Streaming mode
Fixed a crash when sending high speed long Ethernet messages
Fixed a crash when simulating certain VSBs
Fixed a crash when trying certain $31 ISO14229 Jobs
Fixed a crash when using the Function Block Search GUI
Fixed a crash while monitoring Signal Plot
Fixed a 'false positive' problem log when running PC logging in Simulation mode
Fixed a hang when loading certain VS3s
Fixed a hover text showing HTML code instead of text
Fixed a loading issue with CAN-FD ASC Files
Fixed a popup in Simulator showing when it shouldn't have
Fixed a problem where DIDs weren't being Imported or Exported correctly
Fixed a resolution issue on the Signal Plot view
Fixed a scrollbar display issue when using split-screen view
Fixed a typo during certain Problem Log entries
Fixed a typo in the CoreMini Console
Fixed a typo of Receipts in a problem log
Fixed Access Violation when editing certain FB Scripts
Fixed an Access Violation and Crash if the buffer size of a Capture Block was too small
Fixed an Access Violation and Crash when loading a Professional Setup in Basic
Fixed an Access Violation if a Jump To 'landing step' was deleted
Fixed an Access Violation on Diagnostic List view after removing a job
Fixed an Access Violation on the Expression Editor when sort by 'Nodes' was selected
Fixed an Access Violation when changing a physical request Diagnostic
Fixed an Access Violation when clicking the Standalone Logging 'Clean' button
Fixed an Access Violation when converting a VSB to a CSV while online
Fixed an Access Violation when creating a new platform while an existing platform is open
Fixed an Access Violation when modifying Signal Groups
Fixed an Access Violation when opening a Flexray ASC file
Fixed an Access Violation when pressing 'Clear Expression'
Fixed an Access Violation when reviewing FSA with certain databases
Fixed an Access Violation when reviewing VSBs generated via "Split and Combine VSB(s)"
Fixed an Access Violation when shift-clicking.
Fixed an Access Violation when switching Platforms on the Diagnostics List
Fixed an Access Violation when trying to convert a blank .CSV file
Fixed an Access Violation when using "Pwr Man Mode" as a Calculated Signal Limit
Fixed an error popup about Focus with certain customer setups
Fixed an External Exception error when opening certain vs3zip files
Fixed ARXML import not importing signals for NM messages correctly
Fixed AutoUpdate not working properly for the ValueCAN.rf
Fixed CAN Remote Frames not being able to be sent with certain networks
Fixed different instances of a GUI Artifact 'Cannot open the file' from showing
Fixed different networks using different \r \n combinations when logging CSV
Fixed ECU Short and Long description not being populated when importing an A2L into an existing ECU
Fixed ECU Simulator so it no longer misses SWCAN NCA Messages
Fixed ExtensibleSecurity Auto-Unlock jobs not retrying properly after a failed security access attempt
Fixed Fire2s not going online when part of a Multiple-Hardware setup
Fixed Flexray Database messages disappearing if Hide Unused Networks was pressed
Fixed FlexRay PDU data not converting properly from VSB to ASC
Fixed Hex Letter entry (i.e. A, B) from only filling half a byte in the Messages Editor
Fixed how Vehicle Spy reacts to a Limited license on the Professional installation
Fixed Import issues with certain ODX Jobs
Fixed LIN ASC files not importing correctly into other programs
Fixed Min/Max values not being imported correctly
Fixed Mode 9 Decodings not working properly in VehicleScapeDAQ Online Tab
Fixed panels accidentally overlapping in Expression Editor
Fixed problem log for when a DAQ is already open for writing to be more descriptive
Fixed Routines changing names after exporting to ODX
Fixed Signal Editor from having a blank Type dropdown in certain conditions
Fixed Signal Plot to hide the 'Show All' button when not dealing directly with a Legend
Fixed simulation mode transmitting when changing playback speed
Fixed some GUI Overlay issues when using Windows Aero themes
Fixed Typos in Vehicle Spy
Fixed the Capture Block Appended Signal to not reset if the checkbox is unchecked and rechecked
Fixed the DTC Decodings from displaying the DTC number twice in a row
Fixed the Extra Bytes in Receive Filter not working for bytes 8+ for CANFD
Fixed the Fire2 Image from 'Blinking' on the logon screen
Fixed the GM Virtual Networks view incorrectly showing certain VNMFs as running
Fixed the 'Multiframe Setup' button getting stuck pressed
Fixed the Networks View > Statistics > Network Rate to be more accurate
Fixed the Pad Messages option in J1979 Services from being partially hidden
Fixed the Signal Editor being limited to 5 Bytes
Fixed the Split VSB function to be able to handle huge files
Fixed the text being off-screen on certain CoreMini setups
Fixed the Undo button in the J1979 ECUs view not to be disabled
Fixed the VSB to CSV conversion to make sure timestamps are correct
Flow controls now send out on the CAN type they came in on (i.e. FD vs Non-FD)
Function Block Cut action is now disabled while online
Function blocks no longer show 'Running' if you go offline
If a license is expired and there are multiple licenses, there is now a sign saying which is expired
Inherit MAC Address in TCP/IP View with a Fire2 now grabs the Fire2's MAC correctly
ISO14229 Bus Query Snapshot now includes Global and Specific Module DIDs
ISO14229 CAN-FD Diagnostics now work as intended
ISO14229 Write DID commands now have the ability to read output from Read DID jobs
J1979 Diagnostics now has correct Functional Address for both 11- and 29-bit
LIN can now create Schedule Tables based on ARXML Files
LIN Schedule tables created from ARXML files no longer import incorrect wait for times
Log Data Files are now cleared when a ValueCAN.RF CoreMini is cleared
Long CAN-FD transmits now match filters with data bytes in Simulation Mode
ManufacturerRev, DeviceSerial, FirmwareVersion from Physical IO now work in PC Mode (used to be standalone only)
Message Signal "Remove" button is now disabled when online
Message Signals now update to the Static Databyte (if available) when a signal is physically modified in the Messages Editor
Messages Editor filter now refreshes after being cleared with the delete key
Messages Editor sorting no longer displays a duplicate of the first message
Mod mathematical operator no longer needs parentheses to work
Networks > Properties > Protocol List is now sorted
ODX/PDX Import view is now sortable
Pasting of messages from different types of networks (i.e. CAN to Ethernet) is now disallowed
Removed confusing blank panel when creating TCP Transmit messages
Renamed Capture Block "Trigger Options" to be more descriptive
Restricted Mode page now shows the attached Serial Number that doesn't have a license
Settings for Signal Group Logging are no longer reset when unchecked
Setup Platforms Dialog now no longer allows 'bad' inputs
Signal Plot pause button now defaults to pausing the collection instead of scrolling. This can be changed in Options
Signals after byte 256 now work correctly with Function Blocks and other non-Messages View areas
Signals more than 64 bits in length are now supported
Slave VNETs are now supported with 'Run with Remote neoVI'
TCP frame shows up in Diagnostics View when DoIP is selected now
Text Application Signals can now be calculated on interval
The + button in the expression editor now autoselects the new entry
The CoreMini Build Tab details have been compacted to contain only relevant user information
The CoreMini compiler limit for CoreMini size is 65535 bytes on compatible devices
The DPS Job now works with the latest version of DPS (4.33)
The mousewheel now works for scrolling in the Flexray Configuration Tab in ECUs View
The Problem Log for too many function blocks with a basic license now has more clear text
The selected Network in the Messages Editor now persists with the save
The wakeup channel is now imported for Flexray ECUs using ARXML
Time commands now properly prepend a 0 to a 01 to 09 digit
Updated the 'Add X bit signal' to include 32, 64, and 128 bits
Updated the UEF Importer and fixed a bug with ECU IDs not saving correctly
Users can now specify the file extension when using Log Data
Vehicle Spy can now load ASC CANFD files with blank message names
Vehicle Spy is now more Multiple-Hardware friendly! Added a dropdown if two or more devices are detected
Wildcards can now be entered into Rx Message Extra Bytes screen
XCP now supports Multiframe Seed / Keys
XCP over Ethernet (XCPoE) is now supported!
You can now double click to select hardware on the logon screen
MEP	A2L Long Identifiers are now shown in more places
	Fixed a crash while running both XCP and ISO14229 PC DAQ Logging at the same time
	Fixed a possible memory leak in MEP View
	Fixed a text overlap bug in MEP view
	Fixed an Access Violation when loading large XCP Databases
	Fixed CCP A2L Import not setting the correct ArbIDs
	Fixed certain A2Ls not importing Memory Information correctly
	VehicleScapeDAQ now displays 'disabled for edits' if using MEP and changing PC Logging settings
Messages View	ASC files can now be read by CAN Frame description if ArbID isn't available
	Edit Memo now works for Error Messages on the Message View
	Fixed a bug when sorting CSV files
	Fixed a bug where CAN-FD "Add to Rx Message" would store a blank message
	Fixed a bug where CAN-FD messages added from Messages View (Add to Rx Message) added an empty message
	Fixed a bug where certain CSVs in Run Simulation would show all of the relative times to 0
	Fixed a bug where inactive Multiplexed signals would cause bad values to show
	Fixed a bug where Nodes on the Messages View could contain disabled ECUs
	Fixed a bug where setting Filter = On with no filters enabled in Review Buffer would show a blank list
	Fixed a byte display update issue when changing networks
	Fixed a crash when reviewing specific 0x104 VSB buffers
	Fixed an Access Violation after changing the network on a message copied from the Diagnostics View
	Fixed an Access Violation and Crash when pressing the Erase button under certain conditions
	Fixed an Access Violation if 'Go To Line' was used while the line column was sorted
	Fixed an Access Violation when clicking File > New from certain views
	Fixed an Access Violation when dropping a CSV file onto the Messages View
	Fixed an Access Violation when streaming certain VSB Buffers
	Fixed extra Carriage Return Line Feed when saving ASC file with LIN
	Fixed Message View "Find" to work for Line / Count again
	Fixed random grid lines from showing up on the Messages View
	Fixed stability with extremely high EEVB traffic
	Message View Count now starts at 1 after filtering in the Messages View instead of place in the 'total' file
	Messages that match a database message but have an incorrect length now have the DLC highlighted in red
	Messages View Find box is now sorted alphabetically
	Messages View Find selection list is now sorted
	Messages View now has RADGalaxy BR networks in the filter panel
	Messages View Setup Dialog Close button no longer clears Buffer File name
	Out of Order TCP Segments no longer cause the TCP reviewer to be confused. It will now sort out-of-order streams
	Review Buffer Streaming mode now starts at line 1, not 0
	The BLF Exporter no longer allows null or incorrect Network IDs
	You can now use the delete key to remove ECUs (with a popup, of course)
	You no longer get the Network Fixup box if you try to save an empty ASC file
neoVI DLL	Fixed J2534 DLL stating the incorrect version
	J2534 Logging now detects Fire2/Plasma/Ion as correct device
	Updated the J2534 DLL to support CAN-FD
J2534 Device Specific DLL	Added DLL Support for ISO CAN-FD (if available)
	Added SWCAN2 Support for the Fire2 in the device specific DLL
	Fixed a bug where a CAN TX error was read as a CAN-FD Rx message in J2534
	Fixed a bug where a loopback message was tagged as a new CAN-FD message
	Fixed a bug where CAN-FD messages weren't being sent as CAN-FD
neoVI Flex	Optimized neoVI Flex's Transmit code
neoVI Server	Fixed a bug where Plasma and ION wouldn't perform K-Line inits correctly
	Fixed a bug where 'Run with Remote neoVI' wouldn't work if Server was enabled
	Fixed a bug where the SD Card wouldn't reconnect if a slave VNET was under heavy load
	Fixed a crash when going offline with a unit disconnected
	Fixed a possible driver overflow with the FlexRay VNET
	Fixed an Access Violation when using a Plasma or ION with MEP
	Fixed an unreadable popup message when updating PLASMA / ION firmware
	FlexRay VNETs now support much higher bandwidth
RAD-Galaxy	Fixed a bug where the RAD-Galaxy would 'blink' on the Logon Screen
	RAD-Galaxy now supports Logging
	RAD-Galaxy now supports Power Management
ValueCAN.rf	CoreMini Console now correctly reports errors when SD Card data failed to be cleared
	Fixed a bug with Pre/Post trigger on VCAN.rf
	Fixed a bug with the VCAN.rf where it wouldn't wake correctly
	ValueCAN.rf can now log in Standalone with a Current Time based trigger
	ValueCAN.rf can now send K-Line messages on LIN 1/2
	ValueCAN.rf Extractor now will correctly extract even if the file only contains Pre/Post logs
VehicleScapeDAQ	Added a dropdown for Messages per second, that controls Pre/Post trigger capture size
	Added a Single Shot request for J1979 OBD Acquisition in VehicleScapeDAQ
	Added option in PC Logging to change MDF data type and extension
	Added support for XCPoE
	Added support in VehicleScapeDAQ for 64GB Cards
	Adding an application signal to the channels list no longer causes a problem log
	Cleaned up how VehicleScape generates things in the background
	CoreMini Console now properly displays the correct error when trying to generate more than 16 Collections at once
	Diagnostic Tweaker now correctly shows the correct icons again for each state
	Fixed a bug where adding Request All DTCs in VehicleScapeDAQ for one ECU ended up polling them all
	Fixed a bug where 'Force Restart' wasn't working correctly
	Fixed a bug where J1979 PIDs would not be queried correctly in VehicleScapeDAQ
	Fixed a bug where Keyword2000 would stop updating in VehicleScapeDAQ
	Fixed a bug where K-Line Init frames weren't being sent correctly in Standalone
	Fixed a bug where Standard Gateway Configurations wouldn't save correctly
	Fixed a bug where switching from periodic to one-shot ISO14229 in VehicleScape wouldn't actually do one-shots
	Fixed a bug where the Logging button from VehicleScapeDAQ Online View wouldn't stop quick enough
	Fixed a bug with , vs . for numerical groupings (i.e. Europe's 1.000 vs US's 1,000) in VehicleScapeDAQ
	Fixed a bug with MEP and Hardware Acceleration
	Fixed a crash and Access Violation in VehicleScapeDAQ
	Fixed a crash and Access Violation with certain Standalone Setups
	Fixed a crash in PC Logging when pressing Restart on a MDF file
	Fixed a crash when generating a Gateway with VehicleScapeDAQ
	Fixed a crash when spamming Restart in PC Logging
	Fixed a GUI Cutoff in Advanced Generator Options
	Fixed a GUI issue in VehicleScapeDAQ Standalone Logging
	Fixed an Access Violation on VehicleScapeDAQ Channels List
	Fixed an Access Violation if a node without Diagnostic Addresses was selected in VehicleScape 'Select ECUs' list
	Fixed an Access Violation if a VSSAL Application Signal was removed
	Fixed an Access Violation when deleting channels from the channels list
	Fixed an Access Violation when trying to create a standalone setup
	Fixed an Access Violation when trying to generate a collection with an entire bus one-shot report
	Fixed an Access Violation with certain VehicleScapeDAQ Channels
	Fixed ArbIDs for XCPoC not loading correctly from old VS3 Files
	Fixed KWP2K messages not starting on VehicleScapeDAQ Online tab the first time
	Fixed some GUI Radio buttons that were a little too tiny
	Fixed some VSSAL settings not setting the 'Settings have been Changed' flag
	Fixed the 'Enable EtherType Filter' checkbox not being 'sticky' between saves
	Fixed the flickering for all DTCs in the VehicleScapeDAQ Online tab
	Fixed the Gateway 'Clean' button not clearing all messages
	Fixed the GUI text for histograms to note that the sample rate is 0.02s
	Fixed the Message Update Rate (rel) not working in CoreMini
	Fixed the mouse wheel not working when hovering over an edit box in Standalone Logging
	Fixed the reliability of 'Log All Updates' in PC Logging
	Fixed VehicleScapeDAQ Channel Priority for J1979 PIDs
	Fixed VSSAL Collection names from getting lost when the text box lost focus
	Having NeoVI MIC on now forces Generate for Wireless Devices on
	Histograms now round to 5 digits instead of integers
	J1979 Mode $9 Infotypes are now selectable in VehicleScapeDAQ
	J1979 PID Requests now work correctly for VehicleScapeDAQ BusQuery
	J1979 PIDs now decode correctly when used with Standalone Logging
	Optimized CCP polling in VSSAL Scripts
	Optimized the Waiting For process for ISO14229 Polling
	Optimized ValueCAN.rf's XCP Polling routine
	Renamed Bus Query 'Select DIDs' to 'Select DIDs/PIDs'
	Restart Required now properly shows on the VehicleScapeDAQ Online Tab when it's needed
	Seconds boxes now gray out as intended in PC Logging view
	Single Shot Diagnostics has been moved from PC Logging to the Online tab in VehicleScapeDAQ
	The DPID watchdog will now wait for any pending requests before restarting the polling function blocks
	The ISO14229 Polling VSSAL function was optimized
	VehicleScapeDAQ Standalone Logging page has been completely redesigned
	VSDB files are now created with the name of the VS3 appended to the front
	VSSAL Bus Query hyperlinks for J1979 PIDs now jump to the correct PID
	VSSAL Collection names now will remove invalid text from Collection names
When using a one-shot collection, the amount of time to look for each signal is now customizable
Video	Fixed a bug where Video Logging wouldn't work
	The Axis F44 is now supported for Video Logging

Vehicle Spy 3 version 3.7.1.86 to 3.7.1.87 release notes

Vehicle Spy 3 version 3.7.1.85 to 3.7.1.86 release notes

Vehicle Spy 3 version 3.7.1.83 to 3.7.1.85 release notes

Vehicle Spy 3 version 3.7.1.82 to 3.7.1.83 release notes

Vehicle Spy 3 version 3.7.1.73 to 3.7.1.82 release notes

Vehicle Spy 3 version 3.7.0.114 to 3.7.1.73 release notes