7. PHY Dashboard

Note

The Ethernet Phy Dashboard is a debugging tool. It is not intended to be used for every day work flow.

Two primary things are needed to work with the PHY Dashboard.

1. The manufacturer’s data sheet of the PHY. This is needed to know the function of the registers and the format of their contents. These data sheets are usually confidential and require and NDA (Non Disclosure Agreement) with the manufacturer.
2. The address of the PHY in the device and protocol used. If your device is not listed below, please contact support@intrepidcs.com.

Device	Port	MDIO Bus Index	PHY Address	Protocol
RAD-SuperMoon/Moon2	1000BASE-T1	0x0	0x06	Clause45
	1000BASE-T	0x1	0x00
RAD-Moon3	MultiGBASE-T1	0x0	0x00	Clause45
	MultiGBASE-T	0x0	0x10
RAD-Moon Duo	AE1	0x0	0x02	Clause45
	AE2	0x0	0x01
	ETH1	0x0	0x07	Clause22
	ETH2	0x0	0x06
RAD-Pluto PHYs	AE1	0x0	0x04	Clause22
	AE2	0x0	0x05
	AE3	0x0	0x06
	AE4	0x0	0x07
	1000BASE-T	0x0	0x01
RAD-Pluto Switch (SJA1105) Indirect access through MDIO registers: Each switch register access requires reading/writing MDIO address, data, and command registers using 5 addresses shown to the right.	MDIO_ADDRESS_LSB	0x0	0x14	Clause22
	MDIO_ADDRESS_MSB	0x0	0x15
	MDIO_DATA_LSB	0x0	0x16
	MDIO_DATA_MSB	0x0	0x17
	MDIO_OPERATION	0x0	0x18
RAD-Jupiter Switch	88Q5050	0x0	0x10	Clause22
RAD-Jupiter - Internal PHYs PHYs internal to 88Q5050 Access through Switch Address: 0x10	AE1	0x0	0x01	Clause45
	AE2	0x0	0x02
	AE3	0x0	0x03
	AE4	0x0	0x04
	AE5	0x0	0x05
RAD-Jupiter - External PHYs	AE6	0x0	0x02	Clause45
	ETH1	0x0	0x01	Clause22
	ETH2	0x0	0x00
RAD-Epsilon Family - Switch	88Q6113	0x0	0x16	Clause22
RAD-Epsilon - PHYs (and RAD-Epsilon Express)	1	0x0	0x01	Clause45
	2	0x0	0x02
	3	0x0	0x03
	4	0x0	0x04
	5	0x0	0x05
	6	0x0	0x06
	9	0x0	0x10
	10	0x0	0x14
RAD-Epsilon T - PHYs	1	0x0	0x01	Clause45
	2	0x0	0x02
	3	0x0	0x07
	4	0x0	0x05
	5	0x0	0x04
	6	0x0	0x06
	9	0x0	0x10
	10	0x0	0x14
RAD-Gigastar	AE-1	0x0	0x00	Clause45
	AE-2	0x1	0x00
RAD-Comet	ETH01 (100/1000BASE-T)	TBD	TBD	TBD
	AE-01 (100/1000BASE-T1)	TBD	TBD
	AE-02 (10BASE-T1S)	TBD	TBD
	AE-03 (10BASE-T1S)	TBD	TBD

7.1. Opening the PHY Dashboard

The PHY Dashboard can be opened from the Embedded Tools menu in Vehicle Spy (shown below)

7.2. Register Access

MDIO protocol

Most Ethernet Phys communicate using MDIO protocol (Management Data Input/Output). Each frame is 32 bits. There are 2 start bits, a 2 bit operation code, 5 bit phy address, 5 bit register address, 2 bit turn around delay, and 16 bit data.

7.2.1. Clause 22

The initial protocol, IEEE 802.3 Clause 22, was designed to read or write 32 registers within 32 devices. Each read/write is done in one operation.

• Phy Address 5 bits (0 – 31 decimal)
• Register address 5 bits (0 – 31 decimal) or (0 – 1F hex)
• Data 16 bits

Page Register

Some Ethernet Phy manufacturers added a page register to allow for more registers in Clause 22. The page can be 0 – 255 decimal. If the Phy does not support pages, then page will be ignored. When using pages, reads and writes can no longer be performed in one operation. Instead you must write to the page register and then before any other process changes the page, you can read or write the destination register. If another process were to change the page register before you finish, the result will be an read the wrong register or an write to wrong register which may cause the Phy to stop working.

7.2.2. Clause 45

As Ethernet Phys became more complicated and supported different speeds and connections, IEEE 802.3 Clause 45 was added. Because the Register Address is now 16 bits, each read/write takes at 2 operations. The first operation is always writing the Register Address that you want to use in the next operation. The second is the actual read or write. There is also a special read that increments the address after each read which allows you to write a starting address and then read a whole block of registers.

• Port 5 bits (this is equivalent to the Phy Address)
• Device 5 bits (this is similar to the page)
• Register address 16 bits (this allows 65536 registers in each device)
• Data 16 bits

7.3. VSpy Operation

• Add – use this button to add MDIO operations. Ctrl-S saves screen contents to VS3 file.
• Delete – deletes the currently selected item or item.
• Delete All – deletes all operations
• Read One Time – performs all reads from the list once. No writes are performed.
• Write One Time – performs all writes from the list once. No reads are performed.
• All One Time – performs every item in the list once.
• Send Selected – performs only the selected item or items once.
• Start Monitor – performs all reads once per second.
• Stops Monitor – stops the monitor operation.

Note: all values in Hex except Phy Address/Port

7.4. Examples

7.4.1. Clause 22 Example:

• Line 1 writes soft reset to phy address 16, using Clause 22
• Line 2 reads Phy ID Reg1 from phy address 16 using Clause 22
• Line 3 reads Phy ID Reg2 from phy address 16 using Clause 22

7.4.2. Clause 45 Example:

• Line 1 writes soft reset of PCS to Port 16, Device 3 using Clause 45
• Line 2 reads PCS ID Reg1 from Port 16, Device 3 using Clause 45
• Line 3 reads PCS ID Reg2 from Port 16, Device 3 using Clause 45

7.5. Common Clause 22 Registers

Clasuse 22 Registers	Bits	Function/Status
Control Register (Register 0)	15	reset
	14	loopback
	12	auto negotiate
	11	power down
	10	isolate
	9	renegotiate
	8	duplex
	7	collision test
	6/13	speed	10=1000mbps
			01=100mbps
			00=10mbps
Status Register (Register 1)	5	Auto Negotiation Complete
	4	Remote Fault
	3	Auto Negotiation Capability
	2	Link Status
	1	Jabber Detect
	0	Extended Capability
Phy ID Reg 1 (Register 2)	15:0	OUI MSB
PHY ID Reg 2 (Register 1)	15:10	OUI LSB
	9:4	Model Number
	3:0	Revision Number

7.6. Common Clause 45 Registers

7.6.1. PMA/PMD Registers

	Device	Register	Bits	Function/Status
Control Register	1	0	15	reset
			11	power down
			6/13	speed	10=1000mbps
					01=100mbps
					00=10mbps
Device ID Reg 1	1	2	15:0	Auto Negotiation Complete
Device ID Reg 2	1	3	15:10	OUI LSB
			9:4	Model Number
			3:0	Revision Number

7.6.2. PCS Registers

	Device	Register	Bits	Function/Status
Control Register	3	0	15	reset
			14	loopback
			11	power down
			6/13	speed	10=1000mbps
					01=100mbps
					00=10mbps
Device ID Reg 1	3	2	15:0	Auto Negotiation Complete
Device ID Reg 2	3	3	15:10	OUI LSB
			9:4	Model Number
			3:0	Revision Number